YH-1*25天然膠護套電焊機電纜
型號 名稱
Type name
YH 天然膠護套電焊機電纜
YH natural rubber sheath welder cable
YHF 氯丁或其它相當?shù)暮铣赡z彈性體護套電焊機電纜
YHF neoprene or other equivalent synthetic elastomer sheath electric welding cable
的使用要求：
Use requirements of YH electric welding machine cable:
(1)YH電纜是在低電壓(zui高電壓為200V)大電流的條件下工作,要求具有一定耐性。
(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.
(2)焊把線電纜長期允許工作溫度不應超過65℃。
(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.
(3)電機引接線電纜頻繁地移動，扭繞和施放,要求柔軟,彎曲性能好。
(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending perbance.
(4)在施放中易受到尖銳鋼鐵構件的刮、擦,故要求電纜絕緣抗撕、耐磨等機械性能好。
(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.
(5)使用環境條件復雜,如日曬、水沸、接觸泥水、機油、酸堿液體等,要求有一定的耐氣候性和耐油、耐溶劑性。
(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.
(6)有時會碰到熱焊件,要求耐熱變形性好。
(6) sometimes encountered hot weldment, requiring good thermal debation.
(7)經常移動,要求外徑小,重量輕。由于對此種電纜電性能要求不高,且使用環境條件復雜,在結構上要求滿足各種復雜的環境因素是不適宜的。使用時注意改善使用條件,防止外來破壞。
(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical perbance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.
電焊機電纜[1]（YH電纜）全稱高強度橡套電焊機電纜，俗稱焊把線，是YC電纜（通用橡套電纜）的一種。用于電焊機二次側接線及連接電焊鉗、電焊機的專用電纜，其特性是電阻大、電壓低。工作電壓一般為450V到750V。
Electric welding machine cable [1] (YH cable) full of high strength rubber sleeve electric welding cable, commonly known as welding wire, is a YC cable (general rubber cable). For the electric welding machine two secondary side wiring and electrode holder, welding connection cable, its characteristic is high, low voltage resistance. Operating voltage is generally 450V to 750V.
電焊機電纜的結構為單線芯，一般為多跟銅絲組成銅絲組，多組銅絲組則組成電焊機電纜的導體部分，所以YH電纜線體較粗，銅絲數百根。多組銅絲的周圍被一層耐熱聚酯薄膜絕緣包裹。絕緣層一般為純天然橡膠，銅絲為無氧銅，這樣，才能保證線芯的良好導電性及電纜的安全性。
The structure of electric welding machine cable for a single core, usually with copper wire conductor composed of groups, groups of copper group is composed of welding cable, so YH cable body coarse copper wire, hundreds of root. Many groups around the copper wire by a layer of heat-resistant polyester film wrapped insulation. The insulating layer is pure natural rubber, copper wire for copper, so, in order to ensure the safety of wire and cable of good conductivity.
